This is only a preview of the November 2012 issue of Silicon Chip. You can view 22 of the 96 pages in the full issue, including the advertisments. For full access, purchase the issue for $10.00 or subscribe for access to the latest issues. Items relevant to "High-Power Class-D Audio Amplifier, Pt.1":
Items relevant to "High-Energy Ignition System for Cars, Pt.1":
Items relevant to "LED Musicolour: Light Up Your Music, Pt.2":
Items relevant to "Hacking A Mini Wireless Webserver, Pt.1":
Purchase a printed copy of this issue for $10.00. |
This 6000-count true RMS multimeter has a
built-in non-contact voltage detector, low
impedance voltage measurement mode and
the option of a Bluetooth communication
module for wireless data logging.
Review by
NICHOLAS VINEN
Agilent U1233A
True
RMS
DMM
with U1117A Bluetooth Adaptor
siliconchip.com.au
November 2012 71
T
he Agilent U1233A Cat III 600V digital multimeter
can measure AC and DC volts, frequency, resistance,
capacitance, temperature (with a thermocouple), AC
and DC amps and microamps and current frequency. It also
has diode and continuity test (with a beeper), a display
backlight and a built-in LED torch.
Additional modes include relative measurements, max/
min measurements, auto or manual ranging, reading hold/
auto-hold and battery state display.
There are some things we particularly like about this
multimeter. One is that there is no need to change the connections when you switch between amps and microamps
modes as there is a single current measurement terminal.
Also, the fact that it goes up to 60MΩ in resistance mode
is good as many meters will only read to 10MΩ. The bar
graph (below the numeric read-out) makes it easier to interpret rapidly changing readings.
We also like the probes that are supplied. Not only are
they good quality but the probe ends pull off to reveal
insulated banana plugs, making it easy to wire the meter
up to other test equipment with banana sockets, such as
bench supplies.
The selector switch is chunky and is logically laid out;
they haven’t packed a gazillion different modes into one
position. The built-in non-contact voltage detector and
torch are nice touches.
Also, unlike some meters, it uses four AAA cells for
power rather than a 9V battery. 9V batteries are pretty
expensive and don’t usually last that long (especially if
you’re going to use the LED torch a lot).
Features
The non-contact voltage detector is called “Vsense” and is
located at the top of the meter. When you enable this mode
and place that end near a live mains conductor (eg, a wall
power point), you get a beeping sound and a red LED lights
up. You can set the sensitivity to two levels, high and low.
The low-impedance voltage measurement mode is
designed to eliminate false readings caused by inductive
and capacitive coupling into the wires or circuit you are
measuring.
This is especially useful in an environment with a lot of
mains cables but even in a standard office setting, you can
easily get false readings from EMI and hum fields.
One interesting feature is the ability to invert the sense
of the continuity beeper so that it will beep on an open
circuit rather than a short circuit. You can also change the
pitch of the beeper.
The resolution when measuring capacitance is 1nF,
which is higher than we prefer but on the other hand, it will
read capacitances over 10,000µF which is pretty good, with
a test time of around 10s. We like that it shows you when it
is charging and discharging the capacitor under test. Also,
the maximum frequency reading is 100kHz which is a little
low (some meters will go to 10MHz or more).
The basic accuracy of the unit is of the order of ±0.5-1%
for most readings with ±2% for capacitance readings, ±1.5%
for AC current and ±1.0% for DC current (not including
additional lowest digit variation, which is specified in the
data sheet).
Input impedance for voltage readings is 10MΩ in the
normal mode and 3kΩ in the low-impedance mode. The
resolution on the lowest range in each case is 0.1mV (volts
mode), 0.01µA (microamps mode), 1mA (amps mode), 0.1Ω
(resistance mode), 0.001V (diode test/forward voltage) and
0.1°C (thermocouple temperature).
Shown larger than life size for clarity, the U1177A Bluetooth adaptor simply clips onto the back of the meter. It has its
own battery and on/off switch and communicates with the meter through an optical interface. At the top of the meter, you
can see the large lens for the inbuilt LED torch.
72 Silicon Chip
siliconchip.com.au
The test leads supplied with the Agilent U1233A “feel”
much better and more robust than those supplied with
most multimeters, while the probes themselves come apart
(as shown here) so they can accept other fittings.
Bluetooth data logger
While this is a nice multimeter, the real reason for us
getting a unit to review is the U1177A Bluetooth add-on
which clips onto the back. This has its own battery and
communicates with the meter via an optical connection.
With this add-on, connecting to the meter using Bluetooth is easy.
All we had to do in Windows 7 was switch the dongle
to “Setup” mode, tell the operating system to add a new
hardware device, select the Agilent item which popped up
and add the pairing code, which is stated in the provided
set-up guide. Then, when the dongle is switched on and
in range, the meter appears as a pair of serial ports on the
computer.
You can then connect to the serial port via a terminal
program and read out the value currently displayed on the
meter’s screen.
Agilent provide free software, called “Agilent GUI Data
Logger”, which can be used to log and graph this data at
a rate of up to 1Hz. The software can also control some
aspects of the meter, such as turning the backlight on and
off or changing the data range.
While we wouldn’t call this a stellar piece of software, it
works OK and we were able to log data from the multimeter
into a spreadsheet and a graph. Sufficient information is
provided with the U1177A that should you wish to, you
can write your own software to interface with it.
Note that the U1177A adaptor will work with virtually
any Agilent multimeter that has the infrared interface. That
includes the majority made in the last few years.
By the way, if your computer doesn’t have Bluetooth,
you can also get the optional Optical/USB adaptor cable
(U1173A) or just buy a USB-Bluetooth adaptor.
Conclusion and special offer
Currently, Trio Smartcal are offering a free U1177A IR
to Bluetooth DMM Adaptor with the purchase of a range
of DMMs including the U1230 series. This offer is valid
until the end of February 2013.
The U1233A True RMS DMM is $164.95 (+GST). The
slightly less capable U1231A is $98.95 (+GST) while the
U1232A is $141.90 (+GST).
We think that’s a pretty good deal, considering the
U1233A’s provenance and its range of features, especially
when combined with the Bluetooth adaptor. It’s a good
basic True RMS DMM with some nice added features and
it should provide years of faithful service.
For enquiries or purchases, contact Trio on 1300 853 407
or visit http://triosmartcal.com.au
SC
siliconchip.com.au
November 2012 73
|