This is only a preview of the April 2016 issue of Silicon Chip. You can view 43 of the 96 pages in the full issue, including the advertisments. For full access, purchase the issue for $10.00 or subscribe for access to the latest issues. Items relevant to "Touch-Screen Boat Computer With GPS":
Items relevant to "Microwave Leakage Detector":
Items relevant to "Fridge/Freezer Alarm":
Items relevant to "Arduino Multifunction 24-Bit Measuring Shield":
Purchase a printed copy of this issue for $10.00. |
Notes & Errata
Universal Speaker protector Mk3
(November 2015): the SMD bridge
rectifier pads on the published
(RevB) PCB are not wired correctly.
The negative terminal goes go GND
rather than LK1. As a result, if LK1 is
left out but the SMD bridge rectifier
is fitted, it will burn out or a track
will fuse. In this case, cut the track
to the bridge rectifier’s negative pad
(coming from the left side). This is
Advertising Index
fixed with the RevC PCB, which will
be supplied once the stock of RevB
boards is exhausted.
High Visibility 6-Digit LED GPS
Clock, December 2015 & January
2016: the circuit diagram (Fig.1) on
page 39 of the December 2015 issue
shows R8 and R9 swapped. They
are correct on the overlay diagram
(Fig.2) on page 42.
Allan Warren Electronics.............. 95
Altronics.................................. 76-79
Digi-Key Electronics....................... 5
DSCAPE...................................... 95
Glyn Ltd NZ.................................. 17
Hare & Forbes............................. 2-3
High Profile Communications....... 95
Icom Australia.............................. 21
IMP Printed Circuits..................... 11
Jaycar .............................. IFC,45-52
Ask SILICON CHIP
. . . continued from page 95
with a GPS receiver. You would have
to try it but applying 1Hz pulses to
the 1PPS input should keep the time
locked to that source. You would need
to set the initial time manually.
The latest firmware (RevD) adds
a function whereby a button on the
remote can switch the application
of the current time zone on and off,
switching the display between it and
UTC/GMT. If you build two clocks,
you could wire the GPS pins up in
parallel and use a single module. The
clocks should then stay perfectly synchronised. You would need to set them
up using different sets of IR remote
control codes.
Programming the
LCD BackPack
I have ordered the kit for the LCD
BackPack from the February 2016 issue. I am new to Micromite programming, although I have been using the
Proton Basic interface for quite a few
years, so BASIC is fairly simple for
Next Issue
KCS Trade.................................... 15
The May 2016 issue of SILICON CHIP
is due on sale in newsagents by
Thursday 28th April. Expect postal
delivery of subscription copies in
Australia between April 28th and
May 6th.
Keysight Technology..................... 71
me. The only question that I have is
how to link to the Micromite panel to
upload the program. Do I need to build
the ASCII Video Terminal, as described
in the July 2014 issue, to do this? (M.
F., Wyongah, NSW).
• You could use the ASCII Video
Terminal to program the Micromite
LCD BackPack but you don’t have to.
You can use any computer with a serial interface.
Most people would use a USB-toserial adaptor to program the Micromite. This was mentioned/explained
in previous Micromite articles, eg, on
page 33 of the May 2014 issue. It was
also explained in some detail on pages
24 & 25 of the February 2016 issue.
There are plenty of places to get USB
serial interfaces, eg, Jaycar XC4464 and
SC
Altronics Z6225.
Monster Electronics........................ 8
Keith Rippon Kt Assembly ........... 95
LD Electronics.............................. 95
LEDsales...................................... 95
Master Instruments...................... 13
Microchip Technology................... 33
Oatley Electronics........................ 11
Ocean Controls............................ 29
PCBCART...................................... 7
RF Modules Australia............... OBC
Rohde & Schwarz.......................... 9
Rolec OKW.................................. 10
Sesame Electronics..................... 95
SC Radio & Hobbies DVD............ 93
Silicon Chip Binders..................... 90
Silicon Chip Online Shop............. 85
Silicon Chip Subscriptions........... 39
Silicon Chip Wallchart................ IBC
Silvertone Electronics.................. 59
Tronixlabs................................ 38,95
WARNING!
SILICON CHIP magazine regularly describes projects which employ a mains power supply or produce high voltage. All such
projects should be considered dangerous or even lethal if not used safely.
Readers are warned that high voltage wiring should be carried out according to the instructions in the articles. When working on these projects use extreme care to ensure that you do not accidentally come into contact with mains AC voltages or
high voltage DC. If you are not confident about working with projects employing mains voltages or other high voltages, you
are advised not to attempt work on them. Silicon Chip Publications Pty Ltd disclaims any liability for damages should anyone
be killed or injured while working on a project or circuit described in any issue of SILICON CHIP magazine.
Devices or circuits described in SILICON CHIP may be covered by patents. SILICON CHIP disclaims any liability for the infringement of such patents by the manufacturing or selling of any such equipment. SILICON CHIP also disclaims any liability
for projects which are used in such a way as to infringe relevant government regulations and by-laws.
Advertisers are warned that they are responsible for the content of all advertisements and that they must conform to the
Competition & Consumer Act 2010 or as subsequently amended and to any governmental regulations which are applicable.
96 Silicon Chip
siliconchip.com.au
|